Owens Corning Gutter Replacement Nationwide

Owens Corning Gutter Replacement: The Fort Worth Owner’s Guide

Owens Corning gutter replacement in Fort Worth typically runs $9 to $18 per linear foot installed, depending on the gutter profile, fascia condition, and whether downspouts need to be swapped at the same time. Most single-story homes in Fort Worth fall between $1,100 and $2,400 for a full gutter replacement with Owens Corning-compatible components. We stock common Owens Corning gutter profiles and matching hardware on our trucks, and we can usually complete the job the same day we arrive.

Call (682) 900-7902

Most homeowners discover their Owens Corning gutters have failed the hard way: water pouring over the edge during a spring thunderstorm, sagging sections pulling away from the fascia, or rust streaks staining the brick. Sometimes it’s quieter – a slow drip at a seam that rots the fascia board behind it over the course of a year. If the gutters are original to the house and the home is 15 years old or more, the end is usually close.

Key takeaways:

• Installed cost in Fort Worth: $9 to $18 per linear foot
• Your fascia board condition determines whether this is a gutter job or a gutter-plus-carpentry job
• The written price goes on paper before any work begins
• Every replacement is backed by the 365-Day Done Right Promise, in writing

Which Owens Corning Models This Applies To

Owens Corning manufactures septic and basement systems, not residential rain gutters. What Fort Worth homeowners actually have is a gutter system installed alongside Owens Corning roofing products – typically Duration or Oakridge shingles – and the gutter profiles were sourced to complement those roof lines. When we talk about Owens Corning gutter replacement, we’re replacing the gutter system that was installed as part of an Owens Corning roofing package: 5-inch or 6-inch K-style aluminum gutters, matching downspouts, and the hangers, end caps, and miters that tie it all together.

If you’re not sure what you have, check the downspout. Most 5-inch K-style gutters feed 2×3-inch downspouts, while 6-inch gutters feed 3×4-inch downspouts. The gutter profile itself is stamped with the gauge and sometimes the manufacturer mark on the inside channel. The big compatibility gotcha in Fort Worth: if your home was built in the early 2000s with an Owens Corning roof package, the gutters are often 5-inch aluminum in a now-discontinued profile that doesn’t seat cleanly with newer hanger styles. It’s not a problem to replace – it just means new hangers and a re-pitch, not a swap-and-go. For most Fort Worth homes, a quality 0.027-gauge aluminum K-style gutter is the right replacement, and we carry it in white, bronze, and a half-dozen other colors that match Owens Corning roof tones.

Signs Your Owens Corning Gutter Replacement Is Failing

• Water spilling over the front lip during normal rain. This usually means the pitch has gone flat. Gutters need a quarter-inch of fall for every ten feet of run. A Fort Worth foundation shift of half an inch is enough to turn a properly pitched gutter into a standing-water channel.
• Sagging sections pulling away from the fascia. The hangers have pulled loose, usually because the fascia board behind them is water-damaged and the fasteners have nothing to bite into. This is the most common failure in Fort Worth’s older neighborhoods like the Near Southside, where original wood fascia has been exposed to decades of overflow at the eaves.
• Rust streaks or pinhole leaks in the bottom of the channel. Aluminum doesn’t rust, but it does corrode. Standing water from a bad pitch, combined with oak leaves decomposing in the channel, creates an acidic slurry that eats pinholes through the metal in five to seven years.
• Seam separation at the corners or mid-run joints. Seamless gutters have fewer joints, but where they exist, the sealant degrades under Texas sun and thermal cycling. A separated seam leaks a thin stream that rots fascia and soffit slowly and quietly.
• Downspouts dumping water at the foundation. The downspout extension is missing or crushed, and water is saturating the soil right at the slab edge. In Fort Worth’s expansive clay soil, this is how a $400 gutter repair becomes a $12,000 foundation repair.

Replacement Cost & What’s Included

In Fort Worth, Owens Corning-compatible gutter replacement runs $9 to $18 per linear foot installed. A single-story 1,800-square-foot ranch with roughly 160 linear feet of gutter typically lands between $1,500 and $2,200. A two-story home in areas like the Cultural District, where ladder access is tighter and safety setup takes longer, runs toward the upper end of that range.

The price includes removal and disposal of the old gutters, new 0.027-gauge aluminum K-style gutters cut to length on site, downspouts and elbows, hangers, end caps, seam sealing, and a final flow test with a hose. It also includes any necessary re-pitch. What it does not include, and what we’ll flag before we write the number down, is rotten fascia replacement. If the board behind the gutter is soft, that’s a carpentry add-on we price separately and show you on paper before anything gets ordered. Travis Oakley has walked enough Fort Worth roofs to know that the gutter is only as good as the board it hangs from, and we don’t pretend otherwise. The written price you get before any work starts is the price you pay. Every replacement is covered by the 365-Day Done Right Promise, in writing, for one full year, and if it fails within that period, we come back at no charge.

DIY or Call Us?

What an owner can safely do: clean the gutters, check the pitch with a level, confirm downspouts are clear, and look at the fascia board for soft spots or staining. That’s a Saturday morning’s work and it tells you most of what you need to know.

What an owner should not do: hang 160 linear feet of gutter on a two-story elevation off an extension ladder. Most gutter-replacement injuries happen at the ladder-to-roof transition, and a fall from eave height is a broken pelvis or worse. This is not a spring-tension part like a garage door, but the height and the unwieldy 20-foot sections make it a job for a trained crew with proper ladder tie-offs and safety setup. If the gutters are accessible on a single-story and a homeowner has experience working from ladders, replacing a downspout or a short run is reasonable. Full replacement, with seamless runs and correct pitch, is where the savings disappear into re-work and trips to the supplier. Tell me what the roof is doing – we’ll figure out what it needs. Call (682) 900-7902 if you want us to walk the roofline and give you an honest read before you decide.

FAQs